need a tiny bit of help

[mark]

right so the hks rs silver pipe wants blocking off
and the black pipe lower right has the dump valve attached to that
second picture i put on i think
is this correct matey

 

[ElDopesta]

Stick that Dump Vale on as is and tighten the connection with a Jubilee.

Connect the Vacuum Hose on the top of the Dump Valve to where the original one was connected.

Connect a Blocker/Plug on the inlet point which is where your original Recirculating Hose was connected near the inlet Plenum /Throttle Body (or the other way around if you prefer) and the job is over and done with buddy!


El

 

[mark]

that DV need to go into the rear pipe, hard bit i can see in the 1st pic. then the small vaccum hose fits on the top of the DV. Then you need a blanking plug to fit where the stand Valve used to be.

yep got that cheers mate

 

[RsvRob]

right so the hks rs silver pipe wants blocking off
and the black pipe lower right has the dump valve attached to that
second picture i put on i think
is this correct matey

YES

 

[ElDopesta]

Sorry people, I was multi tasking and did not realise how many of us where giving out tuppence worth!!! :whistling: :whistling: :whistling:


El

 

[mark]

Possibly need an overall shot of the engine bay.... just to confirm what pipe is where

think av got it now rob ill have a look tomorrow in day light cheers buddy :awesome:

 

[RsvRob]

Sorry people, I was multi tasking and did not realise how many of us where giving out tuppence worth!!! :whistling: :whistling: :whistling:


El

 

[mark]

Sorry people, I was multi tasking and did not realise how many of us where giving out tuppence worth!!! :whistling: :whistling: :whistling:


El

yep got it now el cheers
the more help the merrier lol

 

[stevolution2010]

you may get running issues with that dumpvalve whenever i fit my other one like yours my car wont run it will tick over an dump on the spot but wont drive!

 

[RsvRob]

Major problem steve if it dumps on the spot!!!! explain more

 

[stevolution2010]

Major problem steve if it dumps on the spot!!!! explain more

i have a baileys dumpvalve an if i fit it to my evo when you rev it it dumps on the spot but cuts out when u drive so i keep my hks ssqv on

but it can also dump on the spot with that fitted

 

[ElDopesta]

It looks like a Forge item so he should be fine.

I have found that they tend to run better if the Atmospheric Valve is attached to the Hard Pipe section as the flutter is less of an issue when it is further away from the Throttle Body.

Even the gormless Baileys devices give no bother! :whistling: :whistling: :whistling:


El

 

[RsvRob]

You can adjust the throttle so it idles at 1000rpm rather than the std 850... this can aid in the stalling.
People do have issues with various VTA bovs. They dump to much air when you come to a sudden stop and the car stalls.

 

[stevolution2010]

You can adjust the throttle so it idles at 1000rpm rather than the std 850... this can aid in the stalling.
People do have issues with various VTA bovs. They dump to much air when you come to a sudden stop and the car stalls.

realy thats good because i prefer the noise from the baileys tbh it dumps like an american truck

how do i adjust revs mate?

 

[sponners]

i have a baileys dumpvalve an if i fit it to my evo when you rev it it dumps on the spot but cuts out when u drive so i keep my hks ssqv on

but it can also dump on the spot with that fitted

sounds like a single piston baileys, they're not designed for maf based cars.

 

[sponners]

if you get your idle control valve set up properly then you should/may fix the stalling issues that you get with a vta.

 

[RsvRob]

Have the engine running at idle when warm and adjust the screw on throttle body at end of the throttle cable. The revs will go up or down and adjust to suit....around 1000rpm

 

[stevolution2010]

sounds like a single piston baileys, they're not designed for maf based cars.

it came off my sierra cosworth

 

[B6lee]

realy thats good because i prefer the noise from the baileys tbh it dumps like a subaruhow do i adjust revs mate?

indeed they do, and for that reason... im out

 

[sponners]

it came off my sierra cosworth

cossies are map based so work fine on them......flog it