dic
New Member
after killing the crankshaft in my evo 4. i have managed to source a evo8 crankshaft with forged pistons. can anyone tell me if a evo8 crank and pistons will fit. and are there any problems i should be aware of.
sponners
Well-Known Member
the 8 crank will fit in the 4, but iirc the centre thrust face is bigger on the 8 crank.
bores will need to be measured regarding the pistons.
bores will need to be measured regarding the pistons.
ElDopesta
Well-Known Member
Hi buddy and welcome to the Forum!!!
Sponners is spot. The Crank will fit with no issues at all. As long as the pistons are standard and not after market (oversized) they will go in a treat. You will just have to take the existing ones out and slide these in. If they are too tight then they are oversized.
I suspect that they are stock so good luck buddy.
Keep us posted right here.
El
Sponners is spot. The Crank will fit with no issues at all. As long as the pistons are standard and not after market (oversized) they will go in a treat. You will just have to take the existing ones out and slide these in. If they are too tight then they are oversized.
I suspect that they are stock so good luck buddy.
Keep us posted right here.
El
dic
New Member
cheers i will let you know how i get on, anything else you guys would recommend doing while im in there?
sponners
Well-Known Member
if your planning on quite a bit of tuning then I would recommend getting a later block as crank walk is quite common on the 4 block.
ElDopesta
Well-Known Member
You will need to replace the head gasket and maybe change the connecting rod bearings that are also known as con rod bearings. Change the Cam Belt kit too and inspect your Clutch kit and the Fly wheel.
An inspection of the turbo would be beneficial too.
Are you doing the work yourself???
El
An inspection of the turbo would be beneficial too.
Are you doing the work yourself???
El
ElDopesta
Well-Known Member
Spot on advice!!
El
El
dic
New Member
not doing the work myself. my mechanic has worked on a few evos but never done the crank on one before so was a bit worried when i told him i had bought an evo8 crank. unfortuanatly he is more into his impreza's. think i will try and source a later evo block then. are the evo 5/6/7/8 blocks all the same which one should i look out for and do i have to change anything to fit
ElDopesta
Well-Known Member
You could go for a V block, simply because it is cheaper.
A VI block has more potential.
You will need to calculate the total cost including the build. It may work out better if you just get an engine.
Work it out and give me a shout. There just might be an engine available for you from a reliable member right here, I think he still may have it.
I have a VI block available but I want you to check what's going on ebay etc. first just in case you might be able to snap up a bargain.
Speak to you soon buddy.
El
El
A VI block has more potential.
You will need to calculate the total cost including the build. It may work out better if you just get an engine.
Work it out and give me a shout. There just might be an engine available for you from a reliable member right here, I think he still may have it.
I have a VI block available but I want you to check what's going on ebay etc. first just in case you might be able to snap up a bargain.
Speak to you soon buddy.
El
El
dic
New Member
could be interested in the evo6 block what are you asking for it?
ElDopesta
Well-Known Member
PM sent buddy.
El
El
sponners
Well-Known Member
theres a guy on mlr put a 6 bottom end up for sale today, main bearings have gone but still runs, hes asking £250 ono
ElDopesta
Well-Known Member
Not a bad deal, all will depend on how much labour your mechanic will charge to change them. Race bearings typically cost between £80 to £100.
Keep us posted buddy.
El
Keep us posted buddy.
El
dic
New Member
cheers i will take a look.
ElDopesta
Well-Known Member
How did you get on with this Diccon???
Do you have any updates for us buddy???
El
Do you have any updates for us buddy???
El
ElDopesta
Well-Known Member
I suspect it is done as you were getting quotes in for insurance.
Just would be nice to know that your back on the road and the mini project is done!
El
Just would be nice to know that your back on the road and the mini project is done!
El
Last edited:
dic
New Member
to finish the story of. i went and got the 6 bottom end on mlr. which never arrived, so took the case through paypal and got my money back. after all this time and hassle i thought i would just get a complete engine. which i now have, just waiting for my mechanic to sort out the squealing sound from the turbo, and preying its not the turbo knackered!
ElDopesta
Well-Known Member
Well keep us posted on that buddy.
Who was this rogue on the MLR that never sent the item out
Name and shame buddy so no one else falls fowl of him
You can post up his User name and his real name as I am sure the paypal address will have listed it.
Mmmm.................that gives me an idea of sorts.
El
Who was this rogue on the MLR that never sent the item out
Name and shame buddy so no one else falls fowl of him
You can post up his User name and his real name as I am sure the paypal address will have listed it.
Mmmm.................that gives me an idea of sorts.
El
dic
New Member
name was robgsr4 or paypal name rob moat. got an email off him after i got my money back. saying he had been locked up in jail and had just been released hence not being able to reply to my emails. don't know whether to give him benefit of the doubt. but either way i won't be buying of him again lol
ElDopesta
Well-Known Member
Here you go mate, lets do it properly and you can be the first to get the ball rolling in the process!!!
You will be making history here
:http://www.evoowners.co.uk/f22/wall-shame-2144.html
El
Nine thousand owners. One garage.
Join free to post in the tech forums, list parts for sale, and get into the members' gallery. Takes a minute.